IRF630 N-قناة الطاقة MOSFET الترانزستور

28.00 جنية

رمز المنتج: T_IRF630 التصنيف:
يشارك:

IRF630 N-قناة الطاقة MOSFET الترانزستور

IRF630 is a third-generation power MOSFET specially designed for applications which required high-speed switching. This component is a great combination of low on-state resistance, cost-effective, and rugged design.

IRF630 is designed to sustain load voltage up to 200 V and 9 A current. It can drive current up to 36 A in pulse mode for 300 μs with a duty cycle of 2%. This Power MOSFET is specially designed to minimize input capacitance and gate change, and available in package TO-220.

 

IRF630 Pinout Configuration 

رقم الدبوس اسم الدبوس Pin description
1 بوابة السيطرة على انحياز MOSFET
2 بالُوعَة التدفقات الحالية من خلال الصرف
3 مصدر التدفقات الحالية من خلال المصدر

 

سمات

  • Extremely high dv/dt capability
  • التبديل السريع
  • Low intrinsic capacitance
  • سهولة الموازاة
  • Gate charge minimized
  • Simple drive requirement

 

IRF630 Equivalent MOSFETs

IRF630 can be replaced by IRFS630, IRFS631, IRF630PBF, IRF640, IRF640PBF, IRF644, IRFB17N50L.

 

التطبيقات

The application of IRF630 is as listed below;

  • Solar power supply application
  • Motor drivers
  • Battery charger
  • Telecommunication applications
  • High-speed switching applications
  • Power management
  • Portable devices

 

Technical Specifications

  • Transistor type: N-channel
  • Maximum applied voltage from drain-to-source (VDS): 200 V
  • Maximum Drain current (continuous) ID: 9 A
  • Maximum Drain Current (Pulse): 36 A
  • Maximum Power dissipation: 74 W
  • On-state resistance between drain and source: 0.40 Ω
  • gate-to-source voltage: ±20 V
  • Gate charge QD: 43 nC
  • Dynamic dv/dt ruggedness: 5.8 V/ns
  • Operating junction and storage temperature range: -55 to 150 ˚C
  • Package: TO-220

 

Note: More technical specifications can be found on the IRF630 datasheet attached at the bottom of this page.

 

IRF630 MOSFET Working with Simulation

A MOSFET can be turned ON by supplying proper gate voltage between the gate and source terminal. If the gate voltage is not applied properly, the MOSFET will remain turn OFF condition. For example, we take IRF630 as MOSFET and use this MOSFET as a switching device to turn ON and OFF a LED. The simulation is done in proteus.

Condition-1: When the applied gate voltage is more than 4 V, the LED will turn ON. Here, we apply 5 V between gate and source.

IRF630 Circuit

Condition-2: When the applied gate voltage is less than 4 V, the LED remains in OFF condition. In this example, the applied gate voltage is 3V, and the LED seems in OFF condition in the figure below.

IRF630 Circuit Diagram

 

ورقة بيانات المكون

 

مقاس
يكتب
عربة التسوق
تسجيل الدخول

لا يوجد حساب بعد؟

إنشاء حساب
اقدر اخدمك ازي يا فندم ؟
مسح الرمز