IR Photoelectric Encoder Sensor 4pin

السعر الأصلي هو: 55.00 EGP.السعر الحالي هو: 48.00 EGP.

  1. Using imported groove optical coupling sensor, width 5mm.
  2. It has the output state light, if output high level, the lights are off. if output low level, it on.
  3. If it covered, it will output high level; otherwise, its output low level.
  4. Good signal and waveform, with a strong driving ability for more than 15mA.
  5. Equipped with a fixed bolt hole, easy install.
  6. Use the LM393 wide voltage comparer.
SKU: IR Encoder Photoelectric Sensor 4pin Categories: ,
Share:

The speed motion sensor utilize a groove IR optocoupler to sense for object between the IR emitter and IR receiver on-board. This methodology allow the module to count the number of obstruction in a given time frame. This characteristic made it very suitable for measuring the speed of rotation.
The digital output is in LOW state when the sensor is not obstructed and the LED will be light up. Digital output will be in HIGH state when the sensor is covered and the LED will be turn off. An on-board potentiometer is available to adjust the sensitivity of the senso

Characteristics:

  • IC: LM393 (dual comparator)
  • Power supply: 3.3V ~ 5.0 V
  • Encoder current consumption: 1.4 mA
  • Interface or type of encoder output signal: TTL digital
  • Output format: digital output (0 and 1)
  • Operating temperature: 0 ? C ~ 70 ? C
  • Dimensions (LxWxH): 32 x 14 x 10 mm
  • The width of the slit groove in probe: 5 mm
  • Diameter for speed sensor mounting holes: 3 mm
  • speed sensor module Weight: 3 g

This is Speed Measuring Sensor Groove Coupler Module For Arduino. The DO output interface can be directly connected to a micro-controller IO port if there is a block detection sensor, such as the speed of the motor encoder can detect.

DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm. Widely used in motor speed detection, pulse count, the position limit, etc.

Wiring Specification :
  1. VCC: The positive 3.3-5 v power supply.
  2. GND: Connect power negative.
  3. DO: TTL switch signal output.
  4. AO: This is analog output.

Feature :

  1. Using imported groove optical coupling sensor, width 5mm.
  2. It has the output state light, if output high level, the lights are off. if output low level, it on.
  3. If it covered, it will output high level; otherwise, its output low level.
  4. Good signal and waveform, with a strong driving ability for more than 15mA.
  5. Equipped with a fixed bolt hole, easy install.
  6. Use the LM393 wide voltage comparer.
  7. The DO output interface can be directly connected to a micro-controller IO port if there is a block detection sensor, such as the speed of the motor encoder can detect.
  8. DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.

Package Includes :

1 x Speed Measuring Sensor Groove Coupler Module For Arduino.

14 Days Warranty

This item is covered with a standard warranty of 14 days from the time of delivery against manufacturing defects only. This warranty is given for the benefit of Micro Ohm customers from any kind of manufacturing defects. Replacement will be done against manufacturing defects.

What voids warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

Shopping cart
Sign in


No account yet?

Create an Account
اقدر اخدمك ازي يا فندم ؟
Scan the code