MT3608 2A Max DC-DC Step Up Power Module Booster Power Module
MT3608 2A Max DC-DC Step Up Power Module Booster Power Module
- It’s efficient up to 93%
- It can source a good amount of current
- The maximum output current: 2A
- Input voltage: 2V-24V DC
- The maximum output voltage: 5V-28V DC
- Description
Description
The MT3608 2A Max DC-DC Step Up Power Module Booster Power Module is a low-cost module that can step-up a 2 to 24V input voltage up to a 5 to 28V output at up to 2A.
DC-DC boost converters step up the input voltage to a higher voltage while also stepping down the available current since the module can’t output more power than its inputs.
This boost converter is adjustable and capable of outputting a voltage in the range of 5.0 to 28V at a continuous current of up to 1.5A depending on input/output voltage settings with 1A available with most settings.
Since it is a boost converter, the input voltage must be lower than the output voltage.
The device is able to use low ESR bulk ceramic capacitors rather than electrolytic caps which avoids long-term aging concerns and contributes to the compact packaging.
The MT3608 converter IC has over-current and thermal limiting features built-in to safely shut the device down if driven too hard.
Voltage Adjustment:
The module has a single-turn potentiometer for adjustment of the output voltage.
Turning the pot CW decreases the output voltage while turning it CCW increases the output voltage.
The upper limit of the adjustment range will depend on the input voltage and the load. With a 9V input for instance, at 1A, the upper voltage limit will be approximately 20V.
Module Connections
These are compact boards with 4 solder pads for making connections.
- VIN = Input Voltage
- VIN- = Ground
- VOUT = Output Voltage
- VOUT- = Ground. Connected to VIN- on the module.
Pad dimensions:

Note:
- The input voltage should not exceed the maximum input voltage.
- Peak current output current is not more than 2A for input & output.
- Please be noted that the output voltage should be higher than the input voltage.
Features :
- It’s efficient by up to 93%.
- It can source a good amount of current.
- It is an inexpensive converter module.
- It’s simple to adjust to get your desired increase in voltage.
Package Include :
1Piece MT3608 2A Max DC-DC Step Up Power Module Booster.
| Input Voltage (V) | 2 ~ 24 |
| Max. Output Current (A) | 2 |
| Operating Temperature (°C) | -40 to 90 |
| Efficiency | 93% |
| Length (mm) | 37 |
| Width (mm) | 17 |
| Height (mm) | 7 |
| Weight (gm) | 4 |
| Shipment Weight | 0.005 kg |
| Shipment Dimensions | 5 × 4 × 3 cm |
Related Products
Three-wire 0.56 inch DC 0V to 100V Digital Voltmeter (Red)
LM2596 Buck Converter DC Voltage Regulator Adjustable Step-Down Power Module with LED Display Voltmeter DC to DC 2.5~40 to 1.25-37V
DC-DC Adjustable Step-Up Boost Converter 150W 6A (10V-32V to 12V-35V)
Power Supply SMPS 24V 2A
AC-DC Module 220Vac to 12Vdc 6A 70W Power Supply Module Switching Power Supply Board
DC Regulated Power Supply M&R APS3005D 5A
Dual Led 0.28 inch DC 100V 100A LED Digital Ammeter-Voltmeter With Shunt
DC-DC Step Up SX1308 Adjustable Power Supply 28V 2A 1.2Mhz Power Booster Module
LM2596S-ADJ DC-DC Buck Converter 4.5-40V to 3-35V 3A Adjustable Step Down Module
Products With Similar Tags
KYORITSU DIGITAL MULTIMETER KEW1021R
STC-1000 AC 220V Digital Temperature Controlled Thermostat Switch STC1000
Power Supply SMPS 12V 42A With Fan (S-500-12)
Uni-T UT33D+ Palm Size Multimeter
Raspberry Pi 4 Model B with 2 GB RAM
DT-06 WiFi Serial Port Transparent Transmission Module TTL to WIFI Compatible with BT HC-06 Interface ESP-M2
DC-DC Adjustable Step-Up Boost Converter 150W 6A (10V-32V to 12V-35V)
Raspberry Pi 5 Model 4GB
Arduino Uno R3 Board without Cable High Quality
INR 18650 Li-ion Battery 3.7v Rechargeable INR (Recycled) 1000-1500mA
18650 Li-ion Battery 3.7v Rechargeable ICR (Recycled) 1000-1500mA
