MPSA42 NPN Transistor

5.00 EGP

SKU: T_MPSA42 Categories:
Share:

MPSA42 Pin Configuration

Pin Number Pin Name Description
1 Emitter Current Drains out through emitter
2 Base Controls the biasing of transistor
3 Collector Current flows in through collector

 

Features

  • Bi-Polar, High Voltage NPN Transistor
  • DC Current Gain (hFE) is 40
  • Continuous Collector current (IC) is 500mA
  • Base- Emitter Voltage (VBE) is 6V
  • Collector-Emitter Voltage (VCE) is 300V
  • Collector-Base Voltage (VCB) is 300V
  • Available in To-92 Package

 

Note: Complete Technical Details can be found at the MPSA42 datasheet given at the end of this page.

 

Alternative NPN Transistors

S9014, S8550S8050BC5472N3904, 2N2369, 2N30552N3906

 

MPSA42 Equivalent NPN Transistors

KST42, MMBTA42, PZTA42.

 

Brief Description on MPSA42

MPSA42 is a NPN transistor hence the collector and emitter will be left open (Reverse biased) when the base pin is held at ground and will be closed (Forward biased) when a signal is provided to base pin. It has a gain value of 30; this value determines the amplification capacity of the transistor, normally MPSA42 will not be used for amplification due to its low gain value. The maximum amount of current that could flow through the Collector pin is 500mA, hence we cannot drive loads that consume more than 500mA using this transistor. To bias a transistor, we have to supply current to base pin, this current (IB) should be limited to 5mA.

When this transistor is fully biased, then it can allow a maximum of 500mA to flow across the collector and emitter. This stage is called Saturation Region and the typical voltage allowed across the Collector-Emitter (V­CE) or Collector-Base (VCB) could be 300V and 300V respectively. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region.

 

Where to use MPSA42

The MPSA42 is a high voltage NPN transistor. A transistor can normally be used as a switch or amplifier, but this transistor is commonly used only for switching purpose since it has a low gain value of 30. The MPSA42 can turn on or turn off high voltage loads (upto 300V) hence they are commonly used for heavy loads or loads that have high peak voltage. Also note that the collector current of the IC is 500mA (0.5A) hence you cannot drive loads which might consume high current. It has a Base-Emitter voltage of 6V hence it can be controlled easily using microcontrollers or other digital electronics.

So if you are looking for an NPN transistor that could switch high voltages with a decent current flow, then the MPSA42 transistor might be the right choice.

 

How to use MPSA42

MPSA42 transistor is normally used to switch high voltage loads or loads that have high peak voltages. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. As mentioned the biasing current should maximum of 5mA. Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin. The value of this resistor (RB) can be calculated using below formulae.

RB = VBE / IB

In the below circuit we have used the MPSA42 transistor to control a high voltage (48V) motor. The resistance (RB) can be calculated using the above formulae as we know the VBE is 5V in this circuit and IB is 5mA. So RB is (5/0.005) 1000ohms (1K)

 Circuit using MPSA42 NPN Transistor

When +5V is supplied, the base current flows through the current limiting 1K resistor to the base pin, the transistor is forward biased and thus the motor is connected to ground. If 0V is supplied to base pin, no current flows to base and thus the transistor is reversed biased making the motor to stop. Also note that the operating current of the motor is just 0.4A which is less than the collector continuous current (0.5A) of the transistor.

Applications

  • Switching high voltage loads
  • Used to control loads with high peak voltage
  • Speed control of low current motors
  • Drive high voltage stepper motors
  • Drive high power LED

 

2D Model and Dimensions

If you are designing a PCB or Perf board with this component then the following picture from the MPSA42 transistor Datasheet will be useful to know its package type and dimensions.

 MPSA42 NPN Transistor 2D-model

Component Datasheet
MPSA42 Datasheet
 

Size
Type

14 Days Warranty

This item is covered with a standard warranty of 14 days from the time of delivery against manufacturing defects only. This warranty is given for the benefit of Micro Ohm customers from any kind of manufacturing defects. Replacement will be done against manufacturing defects.

What voids warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

Shopping cart
Sign in


No account yet?

Create an Account
اقدر اخدمك ازي يا فندم ؟
Scan the code