5V 2 Channel Relay Module with Optocoupler

السعر الأصلي هو: 60.00 EGP.السعر الحالي هو: 55.00 EGP.

5V 2 Channel Relay Module with Optocoupler

  1. Low Level Trigger Relay Module
  2. Two separate LEDs for On/Off indication of the Relay.
  3. Triggering input voltage 3.3V – 5V
  4. Two separate LEDs for On/Off indication of the Relay
  5. Triggering input voltage 3.3V – 5V 4)
  6. Back EMF protection
  7. Back EMF protection 2 LEDs to indicate when relays are ON.
  8. Works with logic level signals from 3.3V or 5V devices
  9. Opto isolation circuitry
  10. Module with diode current protection, short response time
  11. AC Control Voltage: 250V @max.10A
  12. DC Control Voltage: 30V @max. 10A
Share:

5V 2 Channel Relay Module with Optocoupler

This is a 2 Channel isolated 5V 10A relay module Optocoupler for Arduino PIC ARM. It can be used to control various appliances and other types of equipment with a large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

This relay has a 1×4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays.

The pins are marked on the PCB as:

  • GND – Connect 0V to this pin.
  • IN1 – Controls relay 1, active Low Relay will turn on when this input goes below about 2.0V
  • IN2 – Controls relay 2, active Low Relay will turn on when this input goes below about 2.0V
  • VCC – Connect 5V to this pin. Is used to power the optocouplers
Note: This 5V Dual Channel Relay Module is for low level trigger only. 
About high level and low level-triggered mode:
  1. High-level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way;
  2. Low-level trigger refers to the signal voltage between the input terminal and Earth OV trigger, can be understood as the signal input terminal and the GND negative electrode short circuit triggered away  1-channel relay module connection

Jumper Instruction = The relay can be turned on when we connect 5v to one end and the other to -5v / Gnd, while talking about the jumper, if we short the VCC and the middle pin, then our relay will act as high level-triggered relay means that when we will apply + 5V input on its input pin it will be turned on and when the jumper will be set to “middle and GND”, it will act as a low-level triggered relay, It means that relay will be triggered when we implement the 5V / GND on its input pin.


Features of 5V 2 Channel Relay Module with Optocoupler :

  1. 2 LEDs to indicate when relays are ON.
  2. Works with logic level signals from 3.3V or 5V devices
  3. Opto isolation circuitry
  4. Module with diode current protection, short response time
  5. Around the board with 4 mounting holes, hole diameter 3. 1 mm, easy installation and fixing

Package Includes :

1 x 2 Channel isolated 5V 10A relay module with Optocoupler

Relay Type Low Level Trigger
Logic Input (V) 3.3 ~ 5
Trigger Voltage (VDC) 5
Switching Voltage (VAC) 250@10A
Switching Voltage (VDC) 30@10A
Length (mm) 50.6
Width (mm) 39
Height (mm) 19.5
Weight (gm) 28
Shipment Weight 0.03 kg
Shipment Dimensions 6 × 5 × 3 cm

14 Days Warranty

This item is covered with a standard warranty of 14 days from the time of delivery against manufacturing defects only. This warranty is given for the benefit of Micro Ohm customers from any kind of manufacturing defects. Replacement will be done against manufacturing defects.

What voids warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

You Love that

Raspberry Pi 4 Model-B with 4 GB RAM

3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap Prusa Model HIGH QUALITY

8 Pin IC Base

Shopping cart
Sign in


No account yet?

Create an Account
اقدر اخدمك ازي يا فندم ؟
Scan the code