MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC
MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC
- Fully Compatible with 10/100/1000Base-T Networks
- Integrated MAC and 10Base-T PHY
- Supports One 10Base-T Port with Automatic Polarity Detection and Correction
- Supports Full and Half-Duplex modes
- Programmable Automatic Retransmit on Collision
- Programmable Automatic Rejection of Erroneous Packets
- SPI Interface with Clock Speeds Up to 20 MHz
- For Arduino, SPI, AVR, PIC, LPC, STM32
- Description
Description
MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC
The MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC is a stand-alone Ethernet controller with an industry standard Serial Peripheral Interface (SPI). It is designed to serve as an Ethernet network interface for any controller equipped with SPI.
ENC28J60 Ethernet Module utilizes the new Microchip ENC28J60 a popular Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. This Ethernet LAN module connects directly to most microcontrollers.
The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32.
The ENC28J60 consists of seven major functional blocks
1. An SPI interface that serves as a communication channel between the host controller and the ENC28J60.
2. Control registers which are used to control and monitor the ENC28J60.
3. A dual port RAM buffer for received and transmitted data packets.
4. An arbiter to control the access to the RAM buffer when requests are made from DMA, transmit and receive blocks.
5. The bus interface that interprets data and commands received via the SPI interface.
6. The MAC (Medium Access Control) module that implements the IEEE 802.3 compliant MAC logic.
7. The PHY (Physical Layer) module that encodes and decodes the analog data that is present on the twisted-pair interface.
Features of MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC:
- Fully Compatible with 10/100/1000Base-T Networks
- Integrated MAC and 10Base-T PHY
- Supports One 10Base-T Port with Automatic Polarity Detection and Correction
- Supports Full and Half-Duplex modes
- Programmable Automatic Retransmit on Collision
- Programmable Automatic Rejection of Erroneous Packets
- SPI Interface with Clock Speeds Up to 20 MHz
- The board 25MHZ crystal.
- Programmable Padding and CRC Generation
- The network interface board HR911105A.
- 3.3 V power supply pin.
- Stable performance.
- For Arduino, SPI, AVR, PIC, LPC, STM32.
Package includes :
1 x Mini ENC28J60 Ethernet LAN Network Module
Related Products
WeMos ESP8266 D1 R2 WiFi Development Board
Cable for Arduino Nano (USB 2.0 A to USB 2.0 Mini B) 30cm
Nano 328P Expansion Adapter Breakout Board IO Shield
Arduino Pro Mini ATMEGA328P 5V/16M Blue – Standard Version
Products With Similar Tags
PIC ICD2 PICKit2 PICKIT3 Universal Programming Adapter Programmer Board
Mijing SW-03 Rosin Atomizer Mainboard Short Circuit Detector Pen
Electronic Key Lock Switch 12mm 2 position ON/OFF V3 (KS-02-101-Key)
Toshiba 950mAh AAA Ni-MH Rechargeable Battery – 2 Pieces
Arduino Mega 2560 R3 CH340G ATmel MCU ATMEGA2560-16U Improved Version CH340G Board (Board Only)
Mecanum Omni Wheel 60mm Set Right + Left for Yellow TT Motor (2pcs/set )
ESP-WROOM-32 Wifi Bluetooth Combo Module ESP32 Chip SMD
Turbidity Sensor with Board Module — 5V, Analog & Digital Outputs, Probe + Cable
USB Host Shield v2.0 for Arduino (Uno/Mega) – MAX3421E, ADK, SPI
Raspberry Pi Compute Module 3+ 32GB – DDR2-SODIMM SoM, BCM2837B0
